When a furnace stops heating, the cause is usually something simple: a thermostat set wrong, a clogged air filter, a tripped breaker, a furnace door switch that isn’t closed, or a dirty flame sensor. Those five account for a large share of the “no heat” calls HVAC companies run every November, and you can check all of them in about 20 minutes with no special tools.
This guide walks through the checks in the order a technician would, starting with the easy ones. It also covers the signs that mean you should stop and call a pro, and what typical repairs cost in 2026 so you know whether a quote is in the normal range.
First, a safety check
If you smell gas (a rotten egg or sulfur odor), don’t touch the thermostat, light switches or the furnace. Leave the house and call your gas utility or 911 from outside. The same goes if a carbon monoxide alarm is sounding. CO has no smell, and a cracked heat exchanger or blocked flue can send it into living space. The U.S. Consumer Product Safety Commission recommends a CO alarm on every level of the home and outside sleeping areas, and its carbon monoxide information center explains the warning signs.
Before opening any panel on the furnace, turn off the power. Most furnaces have a switch that looks like a regular light switch on the wall or the side of the unit. Flip it off, and if you’re unsure, also switch off the furnace breaker in your electrical panel.
10 things to check, easiest first
Work through these in order. Many people find the problem by step three or four.
- Thermostat mode and setting. Make sure it’s on “Heat,” not “Cool” or “Off,” and set at least 3 to 5 degrees above the current room temperature. Check that a schedule or “away” setting isn’t overriding you.
- Thermostat batteries. A blank or dim screen often means dead batteries. Many models keep displaying while being too weak to signal the furnace, so swap them anyway if they’re more than a year old.
- Fan setting. If the fan is set to “On” instead of “Auto,” it runs constantly, including between heating cycles, and you’ll feel cool air. Switch it to “Auto.”
- Power switch and breaker. Confirm the furnace service switch is on and the breaker hasn’t tripped. Reset a tripped breaker once. If it trips again, leave it off and call an electrician or HVAC tech.
- Air filter. A clogged filter restricts airflow, and the furnace’s high-limit switch may shut the burners off to prevent overheating. Pull the filter out. If you can’t see light through it, replace it.
- Furnace door. Most furnaces have a safety switch behind the blower compartment door. If the panel isn’t seated firmly after a filter change, the furnace won’t run.
- Gas supply. Check that the gas valve near the furnace is in line with the pipe (open). If other gas appliances like the stove also aren’t working, the problem may be your gas service.
- Vents and returns. Walk the house and make sure supply registers are open and return grilles aren’t blocked by furniture or rugs.
- Outside vent pipes. High-efficiency furnaces vent through white PVC pipes on an outside wall or the roof. Snow, ice, leaves or a bird’s nest can block them and trigger a shutdown.
- Condensate drain. High-efficiency models also produce water. A clogged drain line or a full condensate pump can trip a float switch that stops the furnace. Look for water around the base.
After each fix, restore power and give the furnace a few minutes. Modern furnaces run a startup sequence: the inducer fan starts, the igniter glows or sparks, the burners light, and the main blower comes on 30 to 90 seconds later. Some systems lock out after several failed starts, so cycling the power off for a minute and back on can reset them.
Reading the furnace’s error light
Most furnaces built in the last 20 years have a small window or a light on the control board that blinks a code. A steady glow usually means normal operation. A pattern of flashes, such as three blinks, a pause, then three more, points to a specific fault. The legend is typically printed on a sticker inside the blower door.
Write the code down before you reset anything, because cutting power clears it. Even if you end up calling a technician, telling them “it’s flashing code 3, pressure switch” can shorten the visit and the bill.
Common causes when the basics check out
If the thermostat, filter, power and gas are all fine, the fault is likely one of these parts.
- Dirty flame sensor. This thin metal rod near the burners confirms there’s a flame. When it gets coated, the furnace lights and then shuts off within a few seconds. It is one of the most common winter repairs.
- Failed hot surface igniter. If you hear the inducer fan but the burners never light, the igniter may be cracked or burned out. They typically last several years and are fragile.
- Pressure switch or inducer motor. The furnace checks that exhaust is venting properly before lighting. A blocked vent, a cracked hose or a weak inducer motor can stop it at this step.
- Limit switch. Repeated overheating, often from a dirty filter, can wear out the switch that shuts the burners off.
- Blower motor or capacitor. If the burners light but no air comes out of the vents, the blower motor or its capacitor may have failed.
- Control board. Less common, but a failed board can cause erratic behavior or no response at all.
Cleaning a flame sensor is a reasonable DIY job for a handy homeowner: power off, remove the single screw holding it, rub the rod gently with fine steel wool or very fine sandpaper, and reinstall it. Anything involving the gas valve, burners or heat exchanger is a job for a licensed technician.
What furnace repairs cost in 2026
National averages put a typical furnace repair at roughly $125 to $480, with many jobs landing near $300. Technicians usually bill $75 to $150 per hour, and nights, weekends and holidays can push that to around $140 to $210 per hour. The ranges below include parts and labor and vary by region and furnace brand.
| Problem or part | Typical repair cost | DIY possible? |
|---|---|---|
| Flame sensor clean or replace | $80 to $250 | Cleaning, yes |
| Hot surface igniter | $100 to $250 | Sometimes |
| Limit switch | $100 to $375 | No |
| Thermostat replacement | $190 to $480 | Often, for basic models |
| Gas valve | $200 to $800 | No |
| Control board | $300 to $650 | No |
| Blower motor | $300 to $900 | No |
| Inducer motor | $400 to $1,100 | No |
| Heat exchanger | $1,000 to $3,000 | No |
Example: Dana’s 9-year-old gas furnace kept lighting and then shutting off after about five seconds. The thermostat and filter were fine, and the control board was blinking a flame failure code. A technician cleaned the flame sensor and checked the burners. The bill came to $165, mostly the service call. Had she known the code, she could have cleaned the sensor herself with a $5 pad of steel wool.
When to call a technician
Stop troubleshooting and call a licensed HVAC pro if any of these apply:
- You smell gas or a CO alarm goes off (leave first, then call).
- The breaker trips again after one reset.
- You hear banging, screeching or grinding from the unit.
- You see scorch marks, melted wires or soot around the burner area.
- The furnace short cycles (starts and stops every few minutes) after you’ve changed the filter.
- The burner flame looks yellow or lazy instead of mostly blue.
If the house is getting dangerously cold, protect your pipes while you wait. Open cabinet doors under sinks on exterior walls, let a faucet drip, and use space heaters only with plenty of clearance and never while sleeping.
Repair or replace an older furnace?
Gas furnaces often last 15 to 20 years or more. If yours is near that age and needs an expensive part like an inducer motor or heat exchanger, get a replacement quote at the same time as the repair quote. A common rule of thumb is to weigh replacement when a repair would cost more than about a third of a new system, or when you’ve had several repairs in the last two years. A cracked heat exchanger in an older furnace usually means replacement, since it is a CO risk and the repair is costly.
Example: Marcus has an 18-year-old furnace with an 80% efficiency rating. The tech quotes $2,200 for a heat exchanger. A new 95% furnace installed would run several thousand dollars, but it would also cut his gas use for heating. Given the age and a prior blower repair, he decides the repair money is better spent on replacement. The Department of Energy’s Energy Saver page on furnaces explains how efficiency ratings work if you’re comparing models.
Preventing the next breakdown
Most no-heat calls are preventable with a little routine care.
- Change 1-inch filters every 1 to 3 months during heating season, more often with pets.
- Schedule a professional tune-up each fall before the first cold snap. Techs often clean the flame sensor, test the igniter and check for CO as part of it.
- Keep 2 to 3 feet of clear space around the furnace and don’t store paint or chemicals nearby.
- After snowstorms, clear around outside vent pipes.
- Test CO alarms monthly and replace them according to the manufacturer’s date.
Common questions
Why is my furnace running but blowing cold air?
Check the thermostat fan setting first: “On” runs the blower even when the burners are off. If it’s on “Auto” and still blowing cold, the burners may not be lighting because of a dirty flame sensor, failed igniter, gas supply problem or overheating from a clogged filter.
How do I reset my furnace?
Turn the furnace power switch off, wait about a minute, and turn it back on. Some older furnaces with a blower motor reset button have a small red button on the motor housing. Press it once only. If the furnace keeps locking out, there’s an underlying fault that needs diagnosis.
Can a dirty filter really stop a furnace from heating?
Yes. A clogged filter starves the furnace of airflow, the heat exchanger overheats, and the limit switch shuts off the burners. The blower may keep running and push cool air. Replacing the filter often fixes it, though repeated overheating can wear out the limit switch.
How long should a furnace take to start blowing warm air?
Most gas furnaces start blowing warm air within about one to two minutes after the thermostat calls for heat. The inducer fan starts first, then ignition, then the burners, and finally the main blower once the heat exchanger warms up.
Is it safe to run a furnace with the error light flashing?
A flashing code means the furnace detected a fault and usually shuts itself down for safety. Don’t bypass safety switches or keep resetting it repeatedly. Note the code, try the basic checks, and call a technician if it persists.
Before you call for service
- Thermostat on Heat, set above room temperature, fresh batteries.
- Filter replaced and furnace door fully closed.
- Power switch on and breaker not tripped.
- Gas valve open and outdoor vents clear of snow or debris.
- Error code written down from the control board light.
- Furnace model number and age noted (it’s on the label inside the door).
Having this ready helps the technician diagnose faster, and it keeps you from paying a service call for a dead thermostat battery.
Editorial note: This article is general information, and repair costs were checked as of November 2026 and vary by region and equipment. For gas leaks or CO alarms, contact your gas utility or emergency services, and follow your furnace manufacturer’s manual or a licensed HVAC technician for repairs.