How to Weatherstrip a Door: Stop Drafts in an Afternoon

To weatherstrip a door, you seal the two places air sneaks through: the gap between the door and the frame on the sides and top, and the gap under the door. For the frame, you clean the door stop and press in a compressible seal such as foam tape, V-strip or a rubber kerf strip. For the bottom, you add or replace a door sweep or adjust the threshold. Most exterior doors take an hour or two and cost $20 to $60 in materials.

It’s one of the cheapest winter fixes you can make. A drafty door makes a room feel colder than the thermostat says, lets in dust and bugs, and makes your furnace run longer. ENERGY STAR estimates homeowners can save an average of 15% on heating and cooling costs by sealing air leaks and adding insulation, and doors are one of the easiest places to start.

Signs your door needs new weatherstripping

Old weatherstripping flattens, cracks and pulls loose over time. Look for any of these:

  • You can feel cold air moving around the edges on a windy day.
  • Daylight shows around the frame or under the door when it’s closed and the room is dark.
  • The existing seal is torn, brittle, flattened or missing in sections.
  • A dollar bill test fails: close the door on a bill at several points. If it slides out with no resistance, the seal isn’t touching.
  • Rain or snow blows in at the bottom.
  • Higher heating bills with no other explanation.

Another quick test is to hold a lit incense stick near the edges on a breezy day. If the smoke wavers or blows sideways, there’s a leak at that spot.

Types of door weatherstripping compared

The U.S. Department of Energy lists more than a dozen weatherstripping types. For a typical exterior door, the choice usually comes down to the handful below. The price ranges are typical retail costs for one standard door and vary by brand and store.

Type Where it goes Typical cost per door Durability Best for
Foam tape Door stop on sides and top $5 to $15 1 to 3 years Quick fixes and irregular gaps
V-strip (tension seal) Inside of jamb on sides and top $8 to $20 Several years A neat, nearly invisible seal
Kerf-in rubber or foam strip Slot (kerf) in modern door frames $15 to $35 5+ years Replacing factory seals on newer doors
Tubular rubber or vinyl Nailed or screwed to door stop $15 to $30 Several years Older doors with larger gaps
Door sweep Bottom of door, inside face $10 to $30 Several years Gaps under the door
Door shoe or bulb threshold Bottom of door or threshold $20 to $60 Varies with foot traffic Uneven floors, rain exposure

Check your frame before you buy. Many doors made in the last few decades have a thin slot running along the stop where the original seal was pressed in. If you see one, buy a kerf-in replacement and take the old piece to the store to match the profile. If there is no slot, adhesive foam or V-strip is the usual choice.

What you need

  • Weatherstripping for the sides and top, plus 5% to 10% extra for waste
  • A door sweep or threshold seal if the bottom leaks
  • Tape measure, utility knife or sharp scissors
  • Rubbing alcohol and a rag for cleaning
  • Putty knife or flat pry bar for removing old seals
  • Drill and screwdriver for a sweep
  • Hacksaw if you’re cutting a metal sweep to length

DOE recommends installing on clean, dry surfaces and not when it’s below 20°F, since adhesive struggles in the cold. On a freezing day, warm the frame with the furnace running before you start, or do the job from inside with the door closed as much as possible.

How to weatherstrip a door, step by step

  1. Remove the old weatherstripping. Pull kerf-in strips straight out of the slot. Scrape off old foam and adhesive with a putty knife, and pull any nails or staples.
  2. Clean the surface. Wipe the door stop and jamb with rubbing alcohol and let it dry. Adhesive won’t hold on dust, old glue or grease.
  3. Measure each side. Measure the top and both sides of the frame separately, since older frames are rarely square. Write the numbers down.
  4. Cut the strips. Cut each piece to length. Make the side strips run all the way to the top so the corners meet tightly with no gap.
  5. Install the top piece first. For adhesive types, peel a few inches of backing at a time and press the strip in place as you go. Place it so the door presses against it when closed. For kerf strips, push the fin into the slot with your thumb, working from one end.
  6. Install the side pieces. Start at the top and work down. On the hinge side, keep the seal on the stop so it doesn’t bind when the door closes.
  7. Test the door. Close and latch it. It should shut with light pressure and feel snug. If it won’t latch, the seal is too thick, so switch to a thinner profile.
  8. Fit the door sweep. Cut the sweep to the door’s width. Close the door, hold the sweep against the inside face so the rubber or brush just touches the threshold, mark the screw holes, drill pilot holes and screw it on. Most sweeps have slotted holes so you can adjust the height.
  9. Check for light and drafts again. Turn off the room lights and look for any daylight, then redo the dollar bill test at several points.

Example: Lisa’s back door leaked so badly she kept a rolled towel against it all winter. The old foam was flat, and there was a quarter-inch gap under the door. She spent $34 on a kerf-in replacement kit and a screw-on sweep, took about 90 minutes to install them, and was able to put the towel away. Her kitchen stopped feeling noticeably colder than the rest of the house.

Fixing the gap under the door

The bottom of an exterior door is often the biggest leak. You have three main options, depending on the gap.

  • Door sweep. A strip of rubber, vinyl or brush mounted to the inside face. It’s the easiest fix for gaps up to about half an inch. Brush sweeps work well on uneven floors.
  • Adjustable threshold. Many exterior doors have a threshold with screws under a cap or rubber insert. Turning the screws raises the threshold to meet the door. Check this first, because it’s free.
  • Replacement threshold insert or door shoe. If the rubber insert in your threshold is worn or the door bottom has a U-shaped shoe that’s torn, replacement parts are sold by profile. Take a piece with you to match it.

If the door drags on carpet after you add a sweep, raise the sweep slightly or choose an automatic sweep, which lifts when the door opens.

Troubleshooting common problems

The door won’t close or latch

The new seal is too thick. Switch to a thinner foam or a V-strip, or move the strip slightly so the door meets it at a lighter angle. You can sometimes adjust the strike plate on the frame so the latch catches.

There’s still a draft at the corners

Corners are where strips most often fail to meet. Add a short piece of foam tape to bridge the gap, or use a corner pad, a small molded seal made for the bottom corners of exterior doors.

The gap is uneven from top to bottom

The door may be sagging on its hinges. Tighten the hinge screws, and if the holes are stripped, replace the top hinge’s center screw with a longer screw that reaches the wall framing. Once the door hangs square, the weatherstripping can do its job.

Example: Ray installed new foam on his front door, but light still showed at the top latch corner. The door had sagged. He replaced one short hinge screw with a 3-inch screw, which pulled the door back into line, and the gap closed without any extra weatherstripping.

When to call a pro or replace the door

Weatherstripping fixes gaps, not damage. Consider a carpenter or a new door if the frame is rotted, the door is warped so it touches in some spots and gaps in others, or the glass in a door panel is fogged between panes. An energy auditor can also find leaks you can’t see. DOE suggests finding one through RESNET or the Building Performance Institute, and if money is tight, your state’s weatherization assistance program may help eligible households at no cost.

Example: Tasha’s 1960s door had a bowed bottom rail and soft wood near the threshold. A sweep and new seals cut the drafts somewhat, but the bottom kept leaking, and she eventually replaced the door. She still installed new seals on her two other exterior doors, which were in good shape.

Common questions

How long does door weatherstripping last?

It depends on the material and how often the door is used. Foam tape often needs replacing every year or two, while rubber, vinyl and V-strip seals can last several years. Check seals each fall before heating season.

Which side of the door does weatherstripping go on?

For the sides and top, the seal goes on the door stop, the strip of trim the door closes against, so the door compresses it when shut. A door sweep usually mounts to the inside face of the door at the bottom.

Can I weatherstrip a door in winter?

Yes, but adhesive needs a clean, dry surface and doesn’t bond well in extreme cold. DOE advises against installing below 20°F. Kerf-in and screw-on products are less sensitive to temperature than peel-and-stick tape.

Is weatherstripping worth it?

For most homes, yes. Materials are inexpensive, the job takes an afternoon, and sealing drafts makes rooms more comfortable right away. Savings depend on your climate and how leaky the door was.

Before you start

  • Check whether your frame has a kerf slot, and bring a piece of the old seal to the store.
  • Measure all three sides and the door width before buying.
  • See whether your threshold is adjustable before buying a new sweep.
  • Pick a dry day, ideally above 20°F, for adhesive products.
  • Do the dollar bill and light tests afterward to confirm the seal works.

Editorial note: This article is general home improvement information, with costs and guidance checked as of November 2026. Prices vary by store and region; follow the product manufacturer’s instructions and see the Department of Energy’s weatherstripping guide for more detail.